100876 Hytec Air Advance Work Supports 1,300 lbs. Capacity UPC #662536238106
Part #100876 Hytec Air Advance Work Supports 1,300 lbs. Capacity
Hytec’s air advance work supports have a spring return plunger which uses air pressure to extend it to contact the workpiece. To support any externally applied loads, the sleeve surrounding the plunger grips the plunger and holds it in place.
Air advance work supports allow the plunger to be retracted out of the way during workpiece load/unload operations. Applying air pressure to the work support gently raises the plunger until it contacts the workpiece. Adjusting the air pressure will vary the plunger contact force. The air pressure within the work support also serves to keep contaminants out.
The No. 100876’s threaded body may be compactly manifold mounted in your fixture or choose the No. 100877 which includes the 100876 work support and a mounting base for installation on a flat surface for conventionally plumbed circuits. Both feature fully corrosion resistant construction.
Extremely close manufacturing tolerances hold the plunger perpendicular to the workpiece and eliminates inaccuracies due to plunger movement during lock-up. After lock-up, the plunger is absolutely rigid and limits elastic deflection to .00007" per 100 lbs. of load. For base only, order number 500036.
Features:
- 1,300 lbs. capacity @ 5,000 psi maximum
- Fully corrosion resistant construction
- Manifold mount or conventional base mounting
- 1,000 psi minimum recommended pressure
Order NO. | Cap. * (lbs.) |
Oil Cap. (cu. in.) |
Advance System |
Mounting Configuration |
100876 |
1,300 | 0.01 | Air | Manifold |
* Based on 5,000 psi max. operating pressure. (Optional Jam Nut) |
Order No. |
Dimensions (In Inches) | ||||
A | B † Seal Dia. |
C | D | E Hex. |
|
100876 | 1 1/4 - 16 UN | 1.171 | 0.334 | 1.531 | 1.125 |
Order No. |
|||||
F Hex. |
Operating Range | K | L Seal |
||
H | J | ||||
100876 | 0.735 | 2.850 | 3.162 | 2.180 | 0.040 |
Order No. |
Dimensions (In Inches) |
G Hex. |
|
100876 | 0.688 |
Order No. |
MANIFOLD MOUNT DETAIL | ||||||||
Cavity Dimensions | Fluid Passage Dimensions | † Air Passage Dimensions |
|||||||
A Thread Size |
B Min. Thread |
C | D Dia. |
E | F Dia. |
G | H | J Dia. |
|
100876 | 1 1/4 - 16 UN | 0.300 | 0.665 0.675 |
1.182 1.196 |
0.343 | 0.121 0.135 |
0.060 | 0.380 0.400 |
0.375 0.377 |
NOTE: † Connector bushing supplied but not shown. |
AIR ADVANCE WORK SUPPORT | ||
Order No. |
Approximate Forces Required To Depress Plunger (lbs.) |
|
* Air Pressure (psi) | Force (lbs.) | |
100876 | 15 | 1.4 |
NOTE: * Min. air pressure. 15 psi, maximum air pressure 30 psi. ** Minor air leakage may occur at or above this pressure. |
Manufacturer | SPX Hytec |
---|
-
100903 Hytec Swing/Pull Clamps - Threaded Body Style - 5000 lbs UPC #662536277297Special Price $1,121.40 was $1,260.00
-
100965 Hytec Double-Acting Swing/Pull Clamp - Manifold Mount - Upper Flange Style UPC #662536302722Special Price $742.65 was $832.10
-
100963 Hytec Double-Acting Swing/Pull Clamp - Manifold Mount - Upper Flange Style UPC #662536302623Special Price $1,018.88 was $1,144.81
-
100899 Hytec Swing/Pull Clamps - Threaded Body Style - 5000 lbs UPC #662536277211Special Price $1,037.47 was $1,165.70
-
100964 Hytec Double-Acting Swing/Pull Clamp - Manifold Mount - Upper Flange Style UPC #662536302715Special Price $1,018.87 was $1,144.80
-
100896 Hytec Single-Acting Swing/Pull Clamp - Manifold Mount - Upper Flange Style UPC #662536273923Special Price $902.02 was $1,013.50
-
100901 Hytec Swing/Pull Clamps - Threaded Body Style - 5000 lbs UPC #662536277235Special Price $1,038.45 was $1,166.80